SECTION 08386
DOUBLE ACTING IMPACT TRAFFIC DOOR
[ULTRA-LITE®
MODEL]
|
GENERAL
NOTES TO SPECIFIER: |
|
THIS
SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE
PREPARATION OF PROJECT OR OFFICE MASTER SPECIFICATIONS. IT FOLLOWS GUIDELINES
ESTABLISHED BY THE CONSTRUCTION SPECIFICATIONS INSTITUTE, AND THEREFORE MAY
BE USED WITH MOST MASTER SPECIFICATION SYSTEMS WITH MINOR EDITING. |
|
EDIT CAREFULLY TO SUIT PROJECT
REQUIREMENTS. MODIFY AS NECESSARY AND DELETE ITEMS THAT ARE NOT APPLICABLE.
VERIFY THAT REFERENCED SECTION NUMBERS AND TITLES ARE CORRECT. (NUMBERS AND
TITLES REFERENCED ARE BASED ON MASTERFORMAT,
1995 EDITION). |
|
THIS SECTION ASSUMES THE
PROJECT MANUAL WILL CONTAIN COMPLETE DIVISION 1 DOCUMENTS INCLUDING SECTIONS
01330–SUBMITTAL PROCEDURES, 01620–PRODUCT OPTIONS, 01630–PRODUCT SUBSTITUTION
PROCEDURES, 01660–PRODUCT STORAGE AND HANDLING REQUIREMENTS, 01770–CLOSEOUT
PROCEDURES, AND 01780–CLOSEOUT SUBMITTALS. CLOSE COORDINATION WITH DIVISION 1
SECTIONS IS REQUIRED. IF THE PROJECT MANUAL DOES NOT CONTAIN THESE SECTIONS,
ADDITIONAL INFORMATION SHOULD BE INCLUDED UNDER THE APPROPRIATE ARTICLES. |
|
THIS IS AN OPEN PROPRIETARY
SPECIFICATION ALLOWING USERS THE OPTION OF APPROVING OTHER MANUFACTURERS
WHICH COMPLY WITH THE CRITERIA SPECIFIED HEREIN. |
|
NOTES TO THE SPECIFIER ARE
CONTAINED IN BOXES AND SHOULD BE DELETED FROM FINAL COPY. |
|
OPTIONAL ITEMS REQUIRING
SELECTION BY THE SPECIFIER ARE ENCLOSED WITHIN BRACKETS, E.G.: [35] [40]
[45]. MAKE APPROPRIATE SELECTIONS AND DELETE OTHERS. |
|
ITEMS REQUIRING ADDITIONAL
INFORMATION ARE UNDERLINED BLANK SPACES, E.G.: _____________ . |
|
OPTIONAL PARAGRAPHS ARE
SEPARATED BY “OR” WITHIN A BOX, E.G.: OR |
|
|
PART
1 GENERAL
65535.1 SUMMARY
A. Section Includes: Double acting, self
closing, fully insulated, 1-3/4 inch (44 mm) thick, impact traffic door [with
extruded aluminum frame].
|
INCLUDE APPROPRIATE
SECTION(S) BELOW FOR OPENING FRAMING AND DOOR FRAMES. RECOMMENDED FRAME IS A
6 INCH (152 mm) STEEL CHANNEL WITH A 3/8 INCH (10 mm) WEB (MC6 X 18.0).
RUBBAIR EXTRUDED ALUMINUM FRAMES CAN BE SPECIFIED IF DESIRED AND ARE INCLUDED
IN THIS SECTION AS AN OPTION. |
B. Related Sections:
|
INCLUDE APPROPRIATE
LANGUAGE BELOW INCLUDING A REFERENCE TO SECTION 01030–ALTERNATES, IF PRODUCTS
SPECIFIED IN THIS SECTION ARE SUBJECT TO ANY ALTERNATE BID ITEMS, AND ADD
SECTION 01030 TO 1.1 B. OTHERWISE DELETE FOLLOWING PARAGRAPH |
C. Alternates:
65535.2 SUBMITTALS
A. Reference Section 01330–Submittal
Procedures; submit the following items:
1. Product Data.
2. Shop Drawings: Show fabrication details and
anchorage. Include door elevations, head, jamb and meeting stile details
including perimeter air seals.
3. Samples: Full range of manufacturer’s
standard color selections for facing material.
4. Quality Assurance/Control Submittals:
a. Manufacturer’s Installation Instructions.
5. Closeout Submittals:
a. Cleaning and Maintenance instructions.
b. Warranty
65535.3 QUALITY ASSURANCE
A. Qualifications:
1. Manufacturer Qualifications: Minimum five
years experience in producing doors of
the type specified.
65535.4 DELIVERY STORAGE AND HANDLING
A. Reference Section 01660–Product Storage and
Handling Requirements.
B. Verify doors were shipped in upright
position.
1. Note specific doors shipped in other than
upright position on bill of lading and contact manufacturer.
C. Store in upright position and follow
manufacturer’s instructions printed on carton.
65535.5 PROJECT/SITE CONDITIONS
A. Existing Conditions: Frames installed under
other sections shall be level and plumb.
65535.6 WARRANTY
A. One year against defects in materials and
workmanship.
PART
2 PRODUCTS
2.1 MANUFACTURERS
A. Manufacturer: RubbAir Door–Division of Eckel
Industries, Inc.;100 Groton Shirley Rd.; Ayer, MA 01432-1050. Telephone: (800)
966-7822, (978) 772-0480. Fax: (978)
772-7114.
|
INSERT NAME, ADDRESS AND PHONE
NUMBERS OF LOCAL DISTRIBUTOR BELOW. |
1. Distributor:
B. Model: Ultra-Lite®.
C. Substitutions: Reference Section
01630–Product Substitution Procedures.
2.2 DOOR
COMPONENTS
A. Internal Frame: 3-1/2 x 1-1/2 inch (90x38
mm) PVC extrusions, full height of nose and jamb edge. 1-1/2 inch (38 mm)
square PVC extrusions at top, bottom and above and below vision panel.
B. Core: 1-1/2 inch (38 mm) thick closed cell
polystyrene foam.
C. Facings: 1/8 inch (3 mm) thick ABS plastic,
5,400 psi (37 MPa) tensile strength, color as selected by architect.
|
SELECT HARDWARE FROM D. OR E.
BELOW; RETAIN ALL SUBPARAGRAPHS. 3/4 INCH CAM RISE IS STANDARD. |
D. Hardware:
1. Cam: “V” cam design; [3/4 inch (19 mm)
standard rise] [1-1/2 inch (38 mm) rise],
cast Meehanite, minimum 45,000 psi (310 MPa) compressive strength, ASTM B 633
zinc plated.
a. Swing: [90x90] [90x180] [90x135] degree
swing.
|
SINGLE ACTING (90X0
DEGREE SWING) DOORS ARE AVAILABLE. CONTACT RUBBAIR FOR DETAILS AND MODIFY
SECTION TITLE AND SUMMARY ARTICLE ACCORDINGLY. |
2. Cam Follower: 1-1/8 inch (28 mm) diameter
by 5/8 inch (16 mm) wide stud mounted needle bearing roller mounted to cast
iron arm; 2,100 lbf (290 kgm) bearing dynamic capacity.
3. Bottom Bearing: [Standard, extruded
aluminum bearing.] [Combination bottom
bearing and jamb guard, cast Meehanite, minimum 45,000 psi (310 MPa)
compressive strength, ASTM B 633 zinc plated.]
4. Hinge Shaft: 1-5/16 inch (33 mm) diameter
full height steel tube, 62,000 psi (430 MPa)
tensile strength.
|
OR |
E. Offset Pivot Hardware:
1. Top Assembly:
a. 11 gauge zinc plated steel enclosure with
screw adjustable “V” plate bearing guide.
b. 11 gauge zinc plated steel door mounting bracket
with case hardened steel clevis pin and two 7/8 inch (22 mm) diameter steel
bearings.
c. 11 gauge zinc plated steel head/jamb
mounting angle.
2. Bottom Assembly:
a. Internal mounted 1-5/16 inch (33 mm)
diameter solid steel plug turned to 3/4 inch (19 mm) diameter at bearing point.
b. Floor/jamb mounted zinc plated steel jamb
guard with integral, low friction, igus bearing.
F. Seals: Less than 5 cfm (.002 m³/s) air
infiltration per linear foot of seal per ASHRAE Bulletin 90-75
1. Jamb and Nose Edge: Replaceable polymer
impregnated woven nylon fabric in hollow-loop configuration.
2. Header: Field installed, adjustable,
polymer impregnated woven nylon fabric in hollow-loop configuration.
3. Sill: 1/16 inch (2 mm) thick neoprene
rubber, factory installed; fixed.
4. Hardware Cutouts: 1/16 inch (2 mm) thick
neoprene rubber, factory installed; fixed.
|
14X16 INCH (355X405
mm) VISION PANEL IS STANDARD; OPTIONS INCLUDE 7-1/2 X 10-1/2 (190X265 mm),
11-½ X 15-1/2 (290X380 mm), 16X18 (405X455 mm) AND 24X24 (610X610 mm). SHOW
PANEL SIZE AND LOCATION ON DRAWINGS. |
G. Vision Panel: [3/16 inch (5 mm) thick
polycarbonate, double glazed in [rubber gasket with radiused corners] [ABS subframe
with mechanical fasteners] and set flush with both door faces.] [Recessed 3/16 inch (5 mm) thick
polycarbonate, single glazed in ABS subframe with mechanical fasteners.]
|
DELETE FOLLOWING HOLD OPEN PIN
IF OFFSET PIVOT HARDWARE IS SELECTED. |
H. Hold Open Pin: 1/4 inch (6 mm) diameter
steel pin with wire ring and 8 inch (205 mm) chain for attachment to jamb.
|
DELETE FOLLOWING CAM SHIELDS IF
OFFSET PIVOT HARDWARE IS SELECTED. |
I. Cam Shields: [1/16 inch (2 mm) black
rubber flap.] [ABS plastic, color to match door facing.]
2.3 [DOOR
FRAMES
A. 2x4 inch (50x100 mm) extruded aluminum “L”
shaped sections, 3/16 inch (5 mm) minimum thickness. Corners mitered,
reinforced and welded.
B. Provide number, type and size of fasteners
to solidly anchor frame in rough opening.]
|
FOLLOWING ACCESSORIES ARE OPTIONAL.
SELECT AS DESIRED AND DELETE OTHERS. |
2.4 ACCESSORIES
|
SELECT BUMPERS FROM STANDARD
RUBBAIR SIZES; SHOW SIZE AND LOCATION ON DRAWINGS. |
A. Bumpers: [1/4 (6 mm) inch thick molded
polyethylene.] [3/8 inch (10 mm) thick crackcord rubber.]
B. Impact Panels: [12 inch (300 mm)] [24 inch
(600 mm)] [36 inch (900 mm)] [48 inch (1.22 m)] high, 1/8 inch (3 mm) thick [vinyl]
[ABS], pad type, color as selected by Architect.
C. Flex Shield: [12 inch (300 mm)] [24 inch
(600 mm)] [36 inch (900 mm)] [48 inch (1.22 m)] high, 3/8 inch (10 mm) thick
crackcord rubber (pad style only).
D. Wear Strips: 1/4 inch (6 mm) thick high
density polyethelene, ____ inches (___
mm) high by full width of panel; black.
|
DELETE FOLLOWING
JAMB GUARDS IF “COMBINATION BOTTOM BEARING AND JAMB GUARDS” WERE SELECTED IN
2.2 D.3. |
E. Jamb Guards: 1/4 inch (6 mm) bent steel
plate, 3x6x8-3/4 inches (75x150x220 mm).
F. Pressure and Wind Load Accessories:
1. Adjustable Spring Compensator.
2. Deep seat cam.
|
FOLLOWING LOCKING DEVICE IS
STANDARD FOR PADLOCK (NOT SUPPLIED); CONTACT RUBBAIR FOR OTHER OPTIONS. |
G. Locking Device: 1 inch (25 mm) i.d. cast aluminum
bushing (2 per leaf) with two 3/16 inch (5 mm) by 30 inch (760 mm) long
galvanized proof coil chains.
H. Transom Flap: 2 ply vinyl, color as selected
by Architect.
|
TRACK PORTS AND MEAT RAIL
CUTOUTS, IF REQUIRED, SHOULD BE SHOWN ON DRAWINGS. |
2.5 FABRICATION
A. Shop Assembly: Fabricate door components
without visible fasteners on face into 1-3/4 inch (44 mm) thick unitized assembly
with facings sonic welded to frame. [Secure hardware assembly to door with 3
inch (75 mm) steel screws through edge of door into internal sub blocking.]
[Secure top offset pivot hardware to door with through bolts into internal
frame; bottom offset pivot hardware with through bolts into door body.]
2.6 SOURCE
QUALITY CONTROL
A. Fabrication Tolerances: Width and height of
each leaf: + 0, -1/8 inch (3 mm).
PART
3 EXECUTION
3.1 EXAMINATION
A. Examine opening in which door will be
installed.
B. Coordinate with responsible entity to
perform corrective work on unsatisfactory conditions.
C. Commencement of work by installer is
acceptance of opening conditions.
3.2 INSTALLATION
A. Follow manufacturer’s instructions.
B. [Install frames plumb and level.]
C. Install door with necessary anchors,
hardware and accessories.
[1. Drill bottom bearing for hold open pin.]
3.3 ADJUSTING
A. Follow manufacturer’s instructions as
required to:
1. Clean and lubricate operating parts.
2. Adjust to open and close smoothly and
freely without binding.
3. Check seals for proper fit.
3.4 CLEANING
A. Clean surfaces soiled by work as recommended
by manufacturer.
B. Remove surplus materials and debris from the
site.
END OF SECTION[1]